Tempering
In the as-quenched state, martensite, in addition to being very hard, is extremely brittle and cannot be used for most applications. Also, any internal stresses that may have been introduced during quenching have a weakening effect.
If the steel has been fully hardened by being quenched from above its critical temperature, tempering can
be used to enhance the ductility and toughness of martensite and relieve the internal stresses. In tempering, the steel is reheated to a specific temperature below its critical temperature for a certain period of time and then cooled at a prescribed rate.
The following example will demonstrate the effectiveness of tempering:
ASTM A193 Grade B7, SAE J429 Grade 8 and ASTM A574 Socket Head Cap Screws are all made from alloy steels. In fact some alloy steel grades can be used to manufacture any of the three final products:
such as 4140 and 4142 alloy steel. The final mechanical properties are the following: ASTM A193 B7
• Tensile Strength: 125,000 PSI minimum (2-1/2-inch and under)
• Yield Strength: 105,000 PSI minimum (2-1/2-inch and under)
• Hardness: HRC 35 Maximum
SAE J429 Grade 8
• Tensile Strength: 150,000 PSI minimum
8
• Proof Strength: 120,000 PSI
• Yield Strength: 130,000 PSI minimum
• Hardness: HRC 33-39
ASTM A574 Socket Head Cap Screw
• Tensile Strength: 180,000 PSI minimum (through ½”), 170,000 PSI minimum (above ½”)
• Proof Strength: 140,000 PSI (through ½”), 135,000 PSI (above ½”)
• Yield Strength: 153,000 PSI minimum
• Hardness: HRC 39-45 (through ½”), HRC 37-45 (above ½”)
The initial heat-treating process is relatively the same for all three products. The parts are heat treated until fully austenitized. The parts are then quenched and tempered in a liquid (oil). This final tempering temperature is what will dictate our final product. The following are the minimum tempering temperatures
for each specification:
• ASTM A193 B7: 1150°F
• SAE J429 Grade 8: 800°F
• ASTM A574: 650°F
As can be seen by the results, a lower tempering temperature will produce a harder and higher tensile strength part for these alloy steels. However, the lower tempering temperatures will also mean lower service conditions, ductility, impact strength and possible fatigue life. For example a B7 has a high- temperature limitation of approximately 750-800°F. The socket head cap screws and grade 8’s have a limitation of approximately 400-500°F.
Annealing
Annealing is used to soften previously cold-worked metal by allowing it to re-crystallize. The term annealing refers to a heat treatment in which a material is exposed to an elevated temperature for an extended time period and then slowly cooled. Ordinarily, annealing is carried out to (1) relieve stresses;
(2) increase softness, ductility and toughness; and/or (3) produce a microstructure. A variety of annealing heat treatments are possible.
Any annealing process consists of three stages:
1. heating to the desired temperature
2. holding or “soaking” at that temperature
3. slowly cooling, usually to room temperature
Time is the important parameter in these procedures
Process Annealing
Process annealing is a heat treatment that is used to negate the effects of cold work that is to soften and increase the ductility of a previously strain-hardened metal.
Stress Relieving
Internal residual stresses may develop in metal pieces in response to such things as cold working.
Distortion and warpage may result if these residual stresses are not removed. They may be eliminated by a stress relief annealing heat treatment in which the piece is heated to the recommended temperature, held
there long enough to attain a uniform temperature, and finally cooled to a room temperature in air. Stress relieving can eliminate some internal stresses without significantly altering the structure of the material.
Normalizing
Steels that have been plastically deformed by, for example, a rolling operation, consists of grains of
pearlite, which are irregularly shaped and relatively large, but vary substantially in size. Normalizing is an annealing heat treatment use to refine the grains and produce a more uniform and desirable size
distribution.
Normalizing is accomplished by heating the material to a temperature above its upper critical temperature. After sufficient time has been allowed for the alloy to completely transform to austenite, a procedure
termed austenitizing, the metal is allowed to cool in the air.
Full Anneal
9
A heat treatment known as full annealing is often utilized in low- and medium-carbon steels that will be machined or will experience extensive plastic deformation during a forming operation. The full anneal cooling procedure is time consuming,
Spheroidizing
Medium- and high-carbon steels having a microstructure containing coarse pearlite may still be too hard to conveniently machine or plastically deform. These steels, and in fact, any steel, may be heat treated or annealed to develop the spheroidite structure. Spheroidized steels have a maximum softness and ductility
and are easily machined or deformed.





